Hugin Mask tab
Hugin Masks tab
The Hugin Masks tab has two functions:
- Creating masks for individual images that include or exclude specific parts of these individual images into your final panorama.
- Cropping one or more of your individual images, like you would do for e.g. fisheye Projection images having a circular area in the middle with a useless black area outside, or scanned images that might have edges that need to be cropped away.
The top-left side of the masks window shows a list of all images in the current project.
For this the Masks tab has in the mid-section on the left side two sub-tabs Masks and Crop, each with it's own functionality. Note that you first have to select an image in the top left before the functionality of both will be enabled.
The blender (default is Enblend) uses any part of a photo overlap to place a seam which can result in part of a person or object being cut by the seam and only appearing in part in the final stitch.
By excluding an area using a mask (exclude mask) you are telling the blender to exclude that region from consideration both when placing the seam and when blending. The result is that you can remove a person or object from the final stitch. You should only exclude a part of one photo if some other photo shows the same part of the scene without that object, otherwise you will get a black empty area in your final panorama.
When you include an object with a mask (include mask) the opposite happens, this simply removes that part of the scene from all other photos. The blender has no choice but to use the region in the photo you selected.
Masks can be saved and reloaded.
The top-left side of the masks window shows a list of all images in the current project. The list box below shows all masks of the active image.
Creating mask polygon
After selecting add new mask set polygon points with left mouse click. Finish polygon with right mouse button or left double click.
Deleting a mask
You can delete the active mask by the delete mask button. The active mask is also deleted by pressing the delete key when all or none points of the current mask are selected.
Select a mask
There are 3 ways to select a mask
- left mouse click inside polygon
- use rubberband around polygon, this works only when the active polygon has no selected points
- use the listbox on the left side
You can select points of the active polygon by clicking on it. To select several points use a rubberband around all points. When holding down the shift key, the newly selected points are added to the existing selection.
Simply drag a point with left mouse button. This works also when more then one point is selected.
Move the whole mask
If you want to move the whole mask, drag the mask with right mouse button. (You have to start dragging inside the polygon.)
You can add a new point to the mask polygon by click with left mouse button while holding down the ctrl key on a line segment. Until you release the left mouse button you can also directly move the newly created point.
You can delete a single point of the active polygon by a right mouse click while holding ctrl key on a point. To delete multiple points drag a rectangle/rubberband with the right mouse button and pressed ctrl key around the points, which should be deleted. When you press the delete key the selected points are deleted.
Attention: When the remaining polygon consists of less than tree points, the delete operation is canceled.
Image cropping shouldn't be confused with a camera's Crop factor, which is something else entirely. Use the Crop tab to indicate the areas of the input images that hugin should exclude from the stitching output. There are three situations where you might want to use crop parameters:
- With a scanned input image, there are usually black edges or marks along the sides of the image.
- With a circular Fisheye Projection image there are black unexposed areas outside the image circle.
- Some lenses have a lot of flaring around the edges which you don't want to keep.
Select the image to be cropped in the list to the left, you can adjust the position of the crop area by dragging the perimeter in the image preview on the right. Multiple images can be selected by holding down the Shift or Ctrl keys while clicking in the image list.
Note that unlike PTGui, setting crop parameters in hugin doesn't change the Field of View or optical centre of your images, it simply indicates areas of the image to be masked out, so you can change the cropping for photos in your project at any stage of the stitching process. In detail, hugin uses the S 'selection' parameter in the i and o script lines instead of the C 'crop' parameter.
Depending on the input image type, cropping has two different behaviours:
- For circular fisheye photos the crop area is a circle.
- For any other input image, the crop area is a rectangle.
The Crop tab features four text boxes for Left, Top, Right and Bottom where you can manually enter the positions of the four edges. The origin is top-left and numbers indicate the distance in pixels from this origin.
Note that numbers can be negative and can extend beyond the width and height of the photo, this is primarily useful for partial fisheye images where the full circle is not visible, in this case the crop circle extends beyond the picture frame.
The default Always center Crop on d,e assumes that all cropping is symmetrical around the optical centre of the lens. This is normal unless you are using the crop feature to remove lens flare, in which case the crop may need to be asymmetrical.
Save and apply crop values
Usually crop values don't vary too much for each lens/camera combination. So instead of always creating an almost same crop for new projects these values can be saved using the 'Save lens...' button in the Hugin Photos tab tab.
To load crop values just select one image in the 'Camera and Lens' tab and load the previously saved lens description file. That also sets the crop for all images in the project that have the same lens number.
The lens description file is a plain text file with a .ini extension.
Hint: On Mac OS use the command key instead of the control key for all above mentioned operations.